Start with the weight and shape of what you want to secure, because that determines how many straps you need and how strong they have to be. So weigh your load first, or look up the weight in the specifications. Guessing usually doesn’t work, because a few pallets or a stack of building materials often weigh more than you think.
Also look at the dimensions and surface of the load. A smooth, round or sloping object slides more easily than a rough package with a flat bottom. With smooth loads you need more straps, or you place anti-slip mats under the load. That way you keep the tension on the strap and everything stays where it belongs.
A rule of thumb: use at least two straps per load, even if it is light. One strap is enough to let it tip or rotate. Two straps, crossed or placed at a sensible distance from each other, give much more grip.
The LC value (Lashing Capacity) is the maximum force with which you may load the strap during lashing. This is the value you pay attention to, not the breaking strength. The breaking strength is the force at which the strap actually breaks, and it is considerably higher. You always calculate with the LC value, so that you retain a safety margin.
You can find the LC value on the label of the strap, usually expressed in daN (decanewtons). An LC of 2,000 daN roughly means that the strap can handle about 2,000 kilos of pulling force in a straight line. Note: this is not a lifting capacity. When lashing with downward tension, the force works differently than when lifting, and a ratchet strap is never intended for lifting anything.
Add up the LC values of your straps and compare that with the weight of your load. If you are driving with a heavy load, the stress from braking, corners and bumps is considerably higher than the stationary weight. So rather choose a bit heavier than too light. Is the label no longer there or illegible? Then leave the strap alone, because without a clear value you don’t know what it can handle.
A wider strap can generally handle more force and sits more stably on your load, while the length determines whether you can actually wrap it all the way around the load. So measure the circumference of your load and add plenty extra for the buckle and the overlap.
For most jobs you will end up with one of these widths:
The material is usually polyester, and that is for good reason. Polyester barely stretches, is resistant to moisture and holds tension well. Do watch out for sharp edges: steel, concrete or stones can cut through a strap. In that case use corner protectors or protective sleeves, so the strap stays intact. A good ratchet strap doesn’t cost much, but a broken strap on the road can turn out very expensive.
For heavy loads you choose a ratchet strap, for light jobs a cam buckle is sufficient, and you mainly use the endless strap as a loop or for specific applications. The type of closure determines how much tension you can put on the strap and how quickly you work.
This is what each type is good at:
Hesitating between a ratchet strap and a cam buckle? For heavier items, simply choose the ratchet strap. It gives more control and firmer tension. If you are looking for the matching tools for your job, you will find everything in one place in our range of tools and accessories.
Most problems with ratchet straps are not caused by the strap itself, but by how it is used. With a few simple habits you prevent the majority of accidents and damage.
Watch out for this:
So check your ratchet straps before every use and throw away damaged straps. After driving a few kilometers, check whether everything is still tight and retighten if necessary. If you can’t figure out which strap suits which job, feel free to contact us, and we’ll help you think it through.
With us you will find everything to secure your load safely and professionally, from light jobs to heavy work. We have more than 40,000 items in stock, so you don’t have to search everywhere. This is what you can expect from us:
Not sure which ratchet strap suits your load? Visit our showroom or take a look at the webshop at bmbshop.nl, and we will help you on your way to the right choice.
There is no fixed replacement period, but you should check every strap before use for fraying, cuts, burnt spots and damaged buckles or hooks. If you see damage or the label has become illegible, replace the strap immediately. With regular use, especially when exposed to sun, moisture or sharp edges, a strap will easily last a few years, but when in doubt, replacing it is always cheaper than damage to your load.
Hook the strap on both sides to sturdy anchor points and thread the loose end through the spool of the ratchet. Pull the excess strap tight by hand and then tighten with the ratchet handle until the load is firmly secured. Make sure the strap is not twisted and click the handle fully closed at the end, so the ratchet cannot open by accident.
Use corner protectors or protective sleeves between the strap and the edge, so the strap cannot cut through. If you don’t have them at hand, you can temporarily use a thick cloth or piece of rubber, but real corner protectors are safer. After the first few kilometers, check whether the protection is still in place.
No, a ratchet strap is intended for securing loads and not for lifting, hoisting or towing. The LC value only applies to lashing and not to lifting, where the load works very differently. For lifting work you need special lifting gear with an approved WLL value (Working Load Limit).
Use at least two straps per load, but with heavier or smoothly loaded items it is wise to use more. Add up the LC values of all straps and make sure this is well above the weight of your load. If you place anti-slip mats under the load, it will sit more firmly and you can better estimate the number of straps needed.
Store them dry, clean and out of direct sunlight, because UV radiation degrades polyester over time. Roll the straps up neatly or tie them together so they don’t get tangled, and clean them with lukewarm water if they have become dirty or greasy. Do not use aggressive cleaning agents or solvents, because they can weaken the fibers.
LC (Lashing Capacity) applies to lashing, i.e. securing loads, while WLL (Working Load Limit) belongs to hoisting and lifting. For ratchet straps on a trailer or truck, you should therefore always look at the LC value on the label. Never use a ratchet strap for lifting work, even if the value seems high enough.
BMB Techniek B.V.
Crommelinbaan 50
2142 EX Cruquius
Maandag t/m vrijdag: 7.30 – 17.00uur
Zaterdag en zondag: gesloten


© All Right Reserved BMB techniek
Webdesign en bouw door ditisABC