The number of teeth you need is determined mainly by the material. You cut wood with fewer teeth than aluminum, and sheet material calls for something different again than solid wood.
These are handy guidelines for a standard circular saw blade of 190 to 210 mm:
If you are looking for a circular saw blade for wood, a 24-tooth blade is a good choice when speed matters more than a nice edge. A 60-tooth blade is much better suited to cabinetry, skirting boards and anything that stays visible. If you want a circular saw blade for aluminum, always check that the blade is actually suitable for non-ferrous metals. A regular wood blade is not made for that.
Few teeth means fast, rough cutting; many teeth means slower cutting, but with a smoother cut. That difference comes from how much material each tooth removes per revolution.
A 24-tooth blade has large gaps between the teeth, known as gullets. A lot of sawdust is cleared in one go, so the blade clogs less easily and runs smoothly through thick wood. The downside: the cut is rougher and can tear out, especially on the underside of the board.
With 60 teeth or more, each tooth takes a small bite. That gives a tight, clean cut with little tear-out. You do cut more slowly, though, and your machine has to work harder. If you push too hard through thick wood with such a fine blade, the blade gets hot and can even burn or discolor.
Tooth count is not the only thing that matters: tooth shape and hook angle also determine how a blade cuts. Two blades with the same number of teeth can perform very differently.
The most commonly used tooth shapes are:
Then there is the hook angle. A positive angle is aggressive and cuts quickly, but requires a bit more control. A negative or small angle is calmer and safer, and therefore better for aluminum and plastic. When choosing a good circular saw blade, you therefore look not only at the number of teeth, but also at the tooth shape. This is usually printed on the blade or in the product description.
The blade must fit not only the material but also your machine. Diameter, arbor hole and speed must match, otherwise you cut unsafely or get a poor result.
Check these points before you buy a new blade:
If you work with a cordless saw, it pays to choose a blade with a thin kerf and a suitable tooth count. That saves battery charge and gives you longer cutting time. If you are looking for a Milwaukee circular saw blade, take a look at our Milwaukee range, where you will find blades that match the well-known cordless machines.
Most problems with a saw blade come from a wrong choice, not from a bad blade. We see these mistakes regularly:
Torn between two blades? Look at the last job you did and what you missed most: speed or finish. That usually gives the answer right away.
At BMB Techniek we know that choosing a saw blade is not always simple. That is why we are happy to help you along, whether you are a DIYer or work on a building site every day.
Can’t figure it out or just want to talk through your job? Contact us and we will find the saw blade that suits you together.
You can tell a blade is dull by the extra force needed to push it, a smoking or burnt cut, more tear-out and a machine that runs heavier. Discoloration of the blade from heat is also a clear signal. Blades with carbide teeth can often be sharpened by a specialist sharpening service, but with cheaper blades replacing them is usually more economical.
We advise against it. A wood blade has a different tooth shape (usually alternate top bevel) and a more aggressive hook angle, which is unsafe with aluminum and quickly damages the blade. For aluminum, choose a blade with triple chip grind (TCG), a negative or small hook angle and 60 to 80 teeth or more, that is explicitly suitable for non-ferrous metals.
Use a blade with 48 to 60 teeth or more and an alternate top bevel (ATB) or triple chip grind (TCG) for laminate and MDF. With a handheld circular saw, cut with the visible side facing down, and with a plunge saw or table saw, with the visible side facing up. A guide rail and a sharp blade further reduce tear-out.
Choose a blade with a thin kerf and a suitable tooth count, so the motor needs less power and your battery lasts longer. Also check the diameter, the arbor hole and the maximum speed, and see whether the blade is suitable for your brand and type of machine. For wood, 24 to 40 teeth are often a good balance between speed and battery charge.
In that case you use a reducing ring that fits exactly between the blade and the spindle. Make sure the ring has the right outer diameter (the arbor hole of the blade) and inner diameter (the spindle of your machine), and that the blade is mounted completely firmly and without play. If the blade is not secured properly, do not cut and check the mounting again.
First note the material you are going to cut, the diameter and arbor hole of your machine, and whether you find speed or a clean finish more important. With that information you can choose the tooth count and tooth shape from the guidelines. If you are still unsure, ask for advice at a specialist retailer such as BMB Techniek, so you do not needlessly buy the wrong blade.
Regularly remove resin and dirt with a special resin remover, because caked-on resin causes extra friction and heat. Store blades dry and separately, so the teeth do not knock against each other or against other tools. Also always use the right blade for the material and do not push too hard, and the blade will stay sharp longer.
BMB Techniek B.V.
Crommelinbaan 50
2142 EX Cruquius
Maandag t/m vrijdag: 7.30 – 17.00uur
Zaterdag en zondag: gesloten


© All Right Reserved BMB techniek
Webdesign en bouw door ditisABC