Drilling reinforced concrete is considerably more difficult than drilling ordinary concrete. The reinforcement — steel bars running through the concrete — creates extra resistance and can seriously damage your drill bit or machine if you don’t know what you’re doing. The right combination of machine, drill bit, and technique makes the difference between a clean hole and a broken bit. In this article, we explain step by step how to approach this.
For reinforced concrete, you need a machine with enough power to drill through both the concrete and the steel. A regular hammer drill is almost always too weak for this. The standard choice is a combination hammer or rotary hammer, also known as an SDS hammer. These machines combine rotation with a powerful hammering action, allowing them to effectively break through hard materials.
For larger holes — think holes for pipes or ventilation ducts — a diamond core drilling machine is the better choice. It works without hammering action and cuts through the material with a diamond drill bit. That may sound contradictory for reinforced concrete, but modern diamond drilling machines are specifically designed to cut through steel reinforcement as well. When in doubt, always opt for more power than you think you need. Underpowering is the fastest route to a broken drill bit and a failed hole.
The drill bit type is at least as important as the machine. For reinforced concrete, there are two main options: SDS-plus bits for smaller holes and diamond bits for larger holes or cleaner results.
You can identify a good diamond bit for reinforced concrete by the label “reinforced” or “gewapend beton” on the packaging. Never use a standard concrete drill bit for reinforced concrete. It is not made for steel and will break quickly.
With the right preparation, drilling in reinforced concrete goes much more smoothly. Follow these steps for a good result:
Even experienced professionals make mistakes when drilling in reinforced concrete. Most problems arise from rushing or using the wrong tools.
The biggest mistake is skipping the reinforcement detection. Without knowing where the steel bars run, you drill randomly and run a high risk of damaging the reinforcement, which can have structural consequences. A second common mistake is continuing to drill with a bit that is already blunt. A blunt bit generates more heat, wears faster, and produces a messy hole. Replace bits on time — it’s cheaper than a new machine.
We also regularly see people applying too much pressure to the machine. More pressure does not mean faster drilling; it means more wear. Let the machine do its job and use the correct hammering setting. With diamond bits, always switch off the hammering action — otherwise you will immediately damage the diamond segments.
Concrete drilling carries serious risks. Flying debris, fine concrete dust, and high noise levels are the main hazards. Always protect yourself properly before you start.
Wear at least the following personal protective equipment:
Also ensure good ventilation at the work site and preferably use a machine with integrated dust extraction or connect an industrial vacuum cleaner. This is not only better for your health, it also keeps your work area clean and your line of sight clear.
At BMB Techniek, we know that drilling in reinforced concrete requires the right combination of machine, drill bit, and knowledge. That is why we offer a complete range for exactly this type of job. Whether you are looking for a rotary hammer for daily use or a core drilling machine for larger holes, we have it in stock.
Visit us in our showroom in Cruquius, browse our complete range online, or contact us if you are unsure which machine or drill bit best suits your job. We are happy to help.
A blunt bit can be recognised by several signs: the machine has to work harder for the same result, you feel more resistance than usual, the bit heats up faster, and the hole comes out less cleanly. Also visually inspect the carbide tip or diamond segments for wear. Replace the bit as soon as you notice any of these signs, because continuing to drill with a blunt bit damages both the material and your machine.
In load-bearing structures such as columns, foundation beams, or prestressed concrete floors, drilling through reinforcement without the approval of a structural engineer is strongly inadvisable. This can affect the load-bearing capacity of the structure and cause structural damage. When in doubt, always consult a structural engineer or the construction drawings before you start, especially in renovation projects in existing buildings.
Never pull the bit straight back by force if it is stuck — that damages both the bit and the machine. Put the machine into reverse (if available) and carefully work the bit loose with a gentle rotating motion. If the bit is truly jammed on a steel bar, use a second bit to drill away some material around the stuck hole to relieve the pressure.
For occasional jobs, renting is certainly a good option, provided you rent a machine that is specifically suitable for reinforced concrete, such as a powerful SDS-max rotary hammer or core drilling machine. Always ask the rental company explicitly about suitability for reinforced concrete and check whether the correct bits are included. Anyone who regularly drills in reinforced concrete will be better off in the long run with their own professional tools from a brand such as Milwaukee or Bosch Professional.
Water cooling is technically required for wet diamond bits to protect the diamond segments and prevent overheating. Indoors, however, that is not always practical. In that case, you can opt for dry diamond bits, which are specifically designed for use without water and feature a different segment design for heat dissipation. Always combine dry diamond bits with dust extraction to capture the fine concrete dust.
There is no universal maximum drilling depth — it depends entirely on the thickness of the structure, the position of the reinforcement, and the purpose of the hole. As a rule of thumb, for through holes (from one side to the other) you should always align the drilling direction with the reinforcement layout. For blind holes, such as for anchors or fixings, maintain a minimum distance of 30 mm from the nearest reinforcement bar. For larger or deeper holes, always consult the structural engineer or the technical specifications of the structure.
Preferably use an industrial vacuum cleaner with a HEPA filter that is approved for fine concrete dust (class M or H). Many professional rotary hammers have a dust extraction port or are compatible with a dust shroud that mounts directly onto the bit. This is not only better for your health due to the silica hazard, but also results in a cleaner work area and better visibility of your drilling position.
BMB Techniek B.V.
Crommelinbaan 50
2142 EX Cruquius
Maandag t/m vrijdag: 7.30 – 17.00uur
Zaterdag en zondag: gesloten


© All Right Reserved BMB techniek
Webdesign en bouw door ditisABC