Milwaukee Heavy Duty Centre Red Landscape — BMB Techniek
0,00 0

Cart

No products in the cart.

Which Drill Do You Use for Concrete, Stone, and Masonry?

For concrete, you use a hammer drill bit (also known as an SDS drill bit); for stone and masonry, a regular masonry bit is usually sufficient. The difference lies in the hardness of the material and the way the bit works through it. A hammer drill bit strikes and rotates simultaneously, which is necessary to get through hard concrete. A masonry bit only rotates and works fine for softer types of stone such as sand-lime brick or brick walls. Choose the wrong bit and you’ll be working up a sweat for nothing.

Concrete, stone, and masonry: what makes the difference?

Not every “hard material” is the same. Concrete is a composite material made of cement, sand, and gravel, making it considerably harder and denser than ordinary brick or sand-lime brick. Masonry consists of stones and mortar joints, and those joints are relatively soft. That may sound like a minor detail, but it completely determines which tool you need.

Masonry bits are made of carbide (widia) and are designed for softer types of stone. They rotate without a hammering action. Hammer drill bits, also known as SDS bits, combine a rotating movement with a hammering impact. That combination is essential for breaking through the hard aggregates in concrete. If you use a masonry bit on reinforced concrete, you’ll literally burn off the tip without getting even a centimeter deeper.

Choosing the right bit for each material type

Choosing the right bit starts with identifying the material. Below is an overview of the most common situations:

  • Brick and sand-lime brick: A regular masonry bit with a carbide tip is perfectly sufficient. No hammer drilling required.
  • Concrete and reinforced concrete: Always use a hammer drill bit (SDS bit) in combination with a hammer drill or SDS rotary hammer. A regular drill is not suitable here.
  • Masonry (stone + mortar joints): A masonry bit is sufficient, but if you’re unsure about the hardness of the stones, you can also use a hammer drill bit on a low impact setting.
  • Aerated concrete (Ytong): This is actually very soft. Use a regular masonry bit without hammer action here, otherwise the material will crumble too much.
  • Natural stone (granite, marble): Here you need a diamond bit, without hammer action but with water cooling.

Not sure about the material? Try it first with a regular masonry bit. If you can’t get through the material or the bit gets very hot, there’s a good chance you’re dealing with harder concrete and need a hammer drill bit.

Matching drill diameter, drill depth, and drill machine to each other

A good bit is only half the job. The machine you’re drilling with also needs to be right. An SDS bit only works properly in a machine with an SDS chuck, such as an SDS-plus or SDS-max rotary hammer. If you try to insert an SDS bit into a regular drill, it simply won’t fit.

For diameter and depth, a practical rule of thumb applies:

  1. Determine the plug size you want to use. The drill diameter must match the plug diameter — for example, an 8 mm plug requires an 8 mm bit.
  2. Add 10 mm to the desired anchoring depth to allow for the space taken up by drilling dust.
  3. Choose your machine based on the job: For a single hole in a brick wall, a hammer drill is fine. For multiple holes in heavy concrete or reinforced concrete, an SDS-plus or SDS-max rotary hammer is considerably more efficient and comfortable.

Also take into account the maximum drill diameter of your machine. A light hammer drill is not suitable for drilling 20 mm or larger holes in concrete. For that, you really need a heavier rotary hammer. Check out our full range if you want to know which machines are available for your application.

Common mistakes when drilling in stone and concrete

Even with the right bit, things often go wrong. These are the mistakes we see most often:

  • Applying too much pressure: More pressure doesn’t mean faster drilling — it means more heat and a faster worn-out bit. Let the machine do the work.
  • No cooling: During prolonged drilling, especially in hard material, temperatures rise quickly. Pause regularly or cool the bit with water (not when hammer drilling).
  • Wrong setting on the machine: Many hammer drills have a switch for drilling without impact (for wood and metal) and drilling with impact (for stone and concrete). If you forget to switch it, you’ll be drilling with a masonry bit without hammer action in concrete. That won’t work.
  • Continuing to use a dull bit: A worn bit can be recognized by heat buildup and the fact that you’re barely making progress. Replace the bit in time.

Another classic mistake: drilling in masonry and accidentally hitting a reinforcement bar. If in doubt, use a rebar detector before you start, especially with structural walls or floors.

Concrete bits and masonry bits from top brands at BMB Techniek

With us you’ll find a complete range of hammer drill bits, masonry bits, and SDS bits from brands that professionals trust every day. Whether you want to drill a single hole in a brick wall or tackle an entire project in reinforced concrete, we have the right bit for every situation.

What we have in store for you:

  • SDS-plus and SDS-max hammer drill bits for concrete and reinforced concrete, in various diameters and lengths
  • Carbide masonry bits for brick, sand-lime brick, and masonry
  • Diamond bits for natural stone and tiles
  • Bits from top brands such as Milwaukee, Bosch, and Rotec
  • Matching rotary hammers and hammer drills for every type of job

Not sure which bit you need for your specific situation? Contact our team. We’ll help you quickly with honest advice, so you don’t end up coming home with the wrong bit.

Frequently Asked Questions

Can I also use a hammer drill bit without the hammering action, for example for wood or metal?

Technically, an SDS hammer drill bit can be set to rotation-only mode (without impact) in some machines, but this is not recommended. Hammer drill bits are not optimized for wood or metal and produce poor results. For those materials, always use a bit specifically designed for that purpose, such as a wood bit or metal bit.

How can I be sure whether my wall is made of concrete or brick?

A simple test is to carefully start drilling with a regular masonry bit. If you get through it easily, it’s likely brick or sand-lime brick. If you notice the bit is barely making progress, gets very hot, or bounces back, you’re almost certainly dealing with concrete. If in doubt, you can also tap on the wall: concrete sounds fuller and harder than hollow or masonry walls.

What do I do if my drill bit gets stuck in the concrete?

Do not force the machine into reverse, as this can damage the bit or the machine. First remove the machine from the bit, then grip the bit with pliers and carefully work it loose with a back-and-forth motion. To prevent jamming, it is advisable to periodically pull the bit back slightly when drilling deeper holes so that the drilling dust can escape.

How long does a hammer drill bit last on average and when should I replace it?

The lifespan depends heavily on the material, the intensity of use, and the quality of the bit. Clear signs that replacement is needed include excessive heat buildup, barely making progress despite using the right machine and settings, or a visibly worn or rounded carbide tip. Cheap bits can wear out after just a handful of holes when used intensively in concrete, while quality bits from brands like Milwaukee or Bosch last considerably longer.

Do I need to use water when drilling in concrete with a hammer drill bit?

No, with hammer drill bits (SDS bits) you do not use water as a coolant. The hammering action continuously breaks loose the drilling dust, which limits heat buildup. Water and electric hammer drills are a dangerous combination in any case. If you want to apply cooling, pause regularly and let the bit cool down in the air. Water cooling only applies to diamond bits for natural stone and tiles.

Can I use SDS bits with a regular hammer drill?

No, that is not possible. SDS bits have a special shank with notches that only fit in machines with an SDS chuck, such as an SDS-plus or SDS-max rotary hammer. A regular hammer drill has a standard keyed chuck, so an SDS bit simply won’t fit. If you want to carry out heavy drilling work in concrete, investing in an SDS rotary hammer is the right step.

What is the difference between SDS-plus and SDS-max, and which one do I need?

SDS-plus is the most common system for light to medium-duty drilling, suitable for bits up to approximately 26 mm in concrete. SDS-max is intended for heavier professional work, such as large diameters (26 mm and above) in reinforced concrete or during prolonged intensive use. For most DIY and light professional applications, SDS-plus is more than sufficient. If you regularly work with heavy structures or large drilling diameters, SDS-max is the better choice.

    Comments are closed

    Op de hoogte van acties en tools?

    * Required field




    • Winkel informatie

    BMB Techniek B.V.
    Crommelinbaan 50
    2142 EX Cruquius

    KVK: 34077426
    BTW: 807236317.B01

    Maandag t/m vrijdag: 7.30 – 17.00uur
    Zaterdag en zondag: gesloten

    Service

    Word lid van onze WhatsApp Community
    Tips, vragen en aanbiedingen — vakmensen onder elkaar
    Lid worden →

    © All Right Reserved BMB techniek

    2026

    Webdesign en bouw door ditisABC